Duct sizing
Calculate the diameter, airflow or air velocity of a duct, then compare standard diameters. Results are indicative: our engineering office confirms the sizing of the ductwork.
Diameter, airflow, velocity
Choose what you are looking for and enter the other two values: the calculation updates automatically.
Circular duct: airflow = velocity × cross-section. Pressure drop estimated for a galvanised duct (roughness 0.15 mm, air at 20 °C), 90° bends counted with a coefficient of 0.3.
Customer area
Tool reserved for our customers
This tool is available with a CAPTAIR & DIMAVENT customer account. Request access: we create your login and send it to you by email.
A specific project? Describe it to our engineering office ↗
Transport velocities in ducts
Minimum values so that the pollutant does not settle in the ductwork, according to the INRS ED 695 guide.
| Pollutant | Examples | Minimum velocity |
|---|---|---|
| Fumes | Zinc and aluminium oxide fumes | 7 to 10 m/s |
| Oil mist | Machining with neat or soluble oil, grinding, bar turning | 12 to 16 m/s |
| Welding and cutting fumes | Arc welding, plasma, laser or oxy-fuel cutting | 15 to 18 m/s |
| Combined welding and grinding network | Welding fumes and grinding dust in the same network (INRS ED 668) | 18 m/s minimum |
| Very fine, light dust | Very fine cotton lint | 10 to 13 m/s |
| Dry dust and powders | Fine rubber dust, bakelite moulding dust, jute lint, cotton and soap dust | 13 to 18 m/s |
| Average industrial dust | Dry sanding abrasive, grinding dust, jute and granite dust, brick cutting, clay and limestone dust | 18 to 20 m/s |
| Heavy dust | Dust from tumbling and shake-out barrels, sandblasting, cast iron boring | 20 to 23 m/s |
| Heavy or damp dust | Damp cement dust, fibre-cement pipe cutting dust, quicklime, wet pneumatic conveying | over 23 m/s |
Source: INRS, practical ventilation guide no. 0, ED 695, table VI “Range of minimum conveying velocities for polluted air in ducts”. Welding fumes and oil mist: CAPTAIR & DIMAVENT values, above the 12 m/s minimum set for welding by INRS guide ED 668.
Airflows by duct diameter
Theoretical airflow in m³/h according to the internal diameter and air velocity.
| Diameter | 10 m/s | 13 m/s | 18 m/s | 20 m/s | 23 m/s | 25 m/s |
|---|---|---|---|---|---|---|
| Ø 100 mm | 285 | 370 | 510 | 565 | 650 | 705 |
| Ø 120 mm | 405 | 530 | 735 | 815 | 935 | 1 020 |
| Ø 150 mm | 635 | 825 | 1 150 | 1 270 | 1 460 | 1 590 |
| Ø 160 mm | 725 | 940 | 1 300 | 1 450 | 1 660 | 1 810 |
| Ø 200 mm | 1 130 | 1 470 | 2 040 | 2 260 | 2 600 | 2 830 |
| Ø 250 mm | 1 770 | 2 300 | 3 180 | 3 530 | 4 060 | 4 420 |
| Ø 300 mm | 2 540 | 3 310 | 4 580 | 5 090 | 5 850 | 6 360 |
| Ø 315 mm | 2 810 | 3 650 | 5 050 | 5 610 | 6 450 | 7 010 |
| Ø 400 mm | 4 520 | 5 880 | 8 140 | 9 050 | 10 400 | 11 310 |
| Ø 500 mm | 7 070 | 9 190 | 12 720 | 14 140 | 16 260 | 17 670 |
| Ø 630 mm | 11 220 | 14 590 | 20 200 | 22 440 | 25 810 | 28 060 |
| Ø 800 mm | 18 100 | 23 520 | 32 570 | 36 190 | 41 620 | 45 240 |
| Ø 1000 mm | 28 270 | 36 760 | 50 890 | 56 550 | 65 030 | 70 690 |
Get a call back from a technician
Contact us
Let’s talk about your installation.
A technician from our engineering office studies your needs and proposes the right solution for your workshop: machine, capture, ductwork and filtration.
Reply within 48 working hours.
Your request, step by step
-
1
You describe your needs
Pollutant, workstations, constraints: a few lines are enough. A photo of the installation helps us a lot.
-
2
Our engineering office studies it
Capture, airflow, ductwork and filtration are sized for your site, together with you if anything needs clarifying.
-
3
You receive a written proposal
Machine, options and price, in detail: you decide with full knowledge of the facts.
- Since 1994in industrial air treatment
- In-house engineering officefrom design to supply
- All brandsfilters and spare parts
- French Fabnetwork member
