French industrial expertise · Since 1994
G4, M5 and F7 filters for air handling units
G4 pre-filters and M5 and F7 panel, bag or compact filters for air handling units, all makes, from your dimensions.

01 / AHU filters G4 to F7
G4, M5, F7: what each class retains
A G4 pre-filter stops coarse particles: visible dust, insects, fibres, coarse pollen. It protects the downstream filters and the coils of the unit.
An M5 filter retains medium dust. An F7 filter stops a large share of fine particles, including most pollen. On the fresh air of an air handling unit, a G4 pre-filter is often combined with an F7 filter.
02 / AHU filters G4 to F7
EN 779 or ISO 16890: reading the label
Since 2018, the ISO 16890 standard has replaced EN 779. It classifies filters by their efficiency on three particle sizes: PM10, PM2.5 and PM1. A filter marked “ISO ePM1 55%” stops at least 55% of particles smaller than 1 micron.
The former classes are still widely used. The equivalences are only approximate, because the two standards do not measure the same thing: a G4 roughly corresponds to ISO Coarse 60%, an M5 to ISO ePM10 50%, an F7 to ISO ePM1 50%.
03 / AHU filters G4 to F7
Panel, bag or compact: choosing the format
The same class comes in several formats. The flat or pleated panel filter, which is thin, is mainly used as a pre-filter. The bag filter offers a large filter area in a small cross-section; the rigid compact filter does the same over a short depth.
In air handling units, the most common frame sizes are 592 × 592 mm, 592 × 287 mm and 287 × 592 mm. Depth, number of bags and frame type vary between manufacturers: note them on the filter in place.
04 / AHU filters G4 to F7
When to replace the unit’s filters
A filter is replaced when its pressure drop reaches the final value set by the manufacturer, read on the unit’s pressure gauge. Beyond that, the airflow falls and the fan uses more energy.
Pre-filters are generally changed more often than the fine filters they protect. The frequency depends on outdoor air pollution, operating hours and airflow.
05 / AHU filters G4 to F7
Ordering the right reference
Send us a photo of the label, or the dimensions (width × height × depth), the class, the filter type, the number of bags and the quantity. We identify the matching reference, whatever the make of the unit.
To change class or format, also give the airflow of the unit: the pressure drop of the new filter must remain compatible with the fan.
Useful answers
Frequently asked questions
What is the difference between a G4, M5 and F7 filter?
The G4 stops coarse particles and is used as a pre-filter. The M5 retains medium dust. The F7 stops a large share of fine particles and is the final filter on the fresh air of many air handling units.
What does “ISO ePM1 55%” mean on a filter?
The filter stops at least 55% of particles smaller than 1 micron, according to ISO 16890, which replaced EN 779 in 2018.
How often should AHU filters be changed?
There is no single interval: go by the pressure drop read on the unit’s gauge. Pre-filters are generally changed more often than final filters.
Do you supply filters for all makes of air handling unit?
Yes. From the dimensions, class and filter type, or a photo of the label, we propose the matching reference.
Continue your selection
Related solutions and guides
Your industrial project
Tell us what you need.
Send us a photo of the label or the dimensions of your filters, with the class and the quantity: we reply with the reference and a quote.
Contact us
Let’s talk about your installation.
A technician from our engineering office studies your needs and proposes the right solution for your workshop: machine, capture, ductwork and filtration.
Reply within 48 working hours.
Your request, step by step
-
1
You describe your needs
Pollutant, workstations, constraints: a few lines are enough. A photo of the installation helps us a lot.
-
2
Our engineering office studies it
Capture, airflow, ductwork and filtration are sized for your site, together with you if anything needs clarifying.
-
3
You receive a written proposal
Machine, options and price, in detail: you decide with full knowledge of the facts.
- Since 1994in industrial air treatment
- In-house engineering officefrom design to supply
- All brandsfilters and spare parts
- French Fabnetwork member
